We've come across the article about Installing A Bathtub directly below on the internet and felt it made perfect sense to talk about it with you on this page.
Setting up a bath tub isn't specifically rocket science, but it does need solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably tough task. If the old bathtub is conveniently accessible, the project can move rapidly; if you need to open up a wall surface to get rid of the old bathtub and also position the new tub, the task is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified on your own for the task as well as are comfortable attempting it. Instead of hiring a contractor to take over a halfway-completed project, it is better to think about using one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This article will certainly aid you mount a brand-new bath tub in your bathroom if you have actually already purchased a new tub and also do not require to change the arrangement of your previous water pipelines.
Your devices as well as material list ought to make up the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, activate the taps to drain pipes any kind of water continuing to be in the system. The process of removing the existing taps can be fairly bothersome because of the restricted access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from transforming throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a connection to the current supply pipes.
If you require to fit a monobloc, then you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washers remain in place in between the faucet as well as the sink. Safeguard the tap in position with the producer given backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former type needs to be connected to the faucet ends first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Using the two wood boards under its feet, position the bath tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the level and changing the feet on the bath tub until the spirit level checks out degree.
To mount taps, fit the bottom of the outermost adaptable tap connector to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Activate the water supply as well as inspect all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the bathtub and also check the overflow outlet as well as the typical outlet for leaks.
Lastly, repair the bath paneling as explained in the producer's instruction manual. Tiling as well as sealing around the bathtub should wait until the bathtub has been made use of at the very least when as this will certainly settle it into its final position.
Planning for the Installment
To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, resulting in difficulties with moisture and also feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components and installations. They are sold in tubes and also cartridges, as well as can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before securing, to allow for the motion experienced when the tub is in usage. The sealant can fracture relatively very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our post about A Step-by-Step Guide to Installing a Bathtub. Thank you so much for spending some time to read our posting. Appreciated our post? Please share it. Let others locate it. We enjoy reading our article about How to Install a Bathtub.
Click